.
那就是为自己的车车做个检修。当然不是普通的的SERVICE啦，我的99年手动FORD FESTIVA一直发动机有噪音，他们说是LIFTER发出来的。查了一下可能有以下的检测和维修方法。
现在我只有一辆车，要是开始修理了没车开也很麻烦......要不等等在说吧。
ENGINE CLICKING NOISES
A clicking or tapping noise that gets louder when you rev the engine is probably "tappet" or upper valvetrain noise caused by one of several things: low oil pressure, excessive valve lash, or worn or damaged parts.
First, check the engine dipstick to see if the oil level is low. If low, add oil to bring it back up to the full mark. Is the engine still noisy? Check your oil pressure. A low gauge reading (or oil warning light) would indicate a serious internal engine problem that is preventing normal oil pressure from reaching the upper valvetrain components. The cause might be a worn or damaged oil pump, a clogged oil pump pickup screen or a plugged up oil filter. Using too thick a viscosity of motor oil during cold weather can also slow down the flow of oil to the upper valvetrain, causing noise and wear.
COLLAPSED LIFTER NOISE
Worn, leaky or dirty lifters can also cause valvetrain noise. If oil delivery is restricted to the lifters (plugged oil galley or low oil pressure), the lifters won't "pump up" to take up the normal slack in the valvetrain. A "collapsed" lifter will then allow excessive valve lash and noise.
VALVE LASH NOISE
If you can rule out lubrication-related problems as a cause, the next step would be to remove the valve cover(s) and check valve lash. On older import engines, mechanical lifters require periodic valve lash adjustments (typically every 30,000 miles). Too much space between the tips of the rocker arms and valve stems can make the valvetrain noisy -- and possibly cause accelerated wear of both parts.
To measure (and adjust) valve lash, you need a feeler gauge. The gauge is slid between the tip of the valve stem and rocker arm (or the cam follower or the cam itself on overhead cam engines) when the piston is at top dead center (valve fully closed). Refer to a manual for the specified lash and adjustment procedure. Also, note whether the lash spec is for a hot or cold engine (this makes a big difference!).
On engines with hydraulic lifters, oil pressure pumps up the lifters when the engine is running to maintain zero lash in the valvetrain. This results in quiet operation. So if the rocker arms are clattering, it tells you something is amiss (bad lifter or worn or damaged parts) or the rocker arms need adjusting.
DAMAGED ENGINE PARTS NOISE
Inspect the valvetrain components. Excessive wear on the ends of the rocker arms, cam followers (overhead cam engines) and/or valve stems can open up the valve lash and cause noise. So too can a bent pushrod or a broken valve spring.
RAPPING OR DEEP KNOCKING ENGINE SOUND
Usually bad news. A deep rapping noise from the engine is usually "rod knock," a condition brought on by extreme bearing wear or damage. If the rod bearings are worn or loose enough to make a dull, hammering noise, you're driving on borrowed time. Sooner or later one of the bearings will fail, and when it does one of two things will happen: the bearing will seize and lock up the engine, or it will attempt to seize and break a rod. Either way your engine will suffer major damage and have to be rebuilt or replaced.
Bearing noise is not unusual in high mileage engines as well as those that have been neglected and have not had the oil and filter changed regularly. It can also be caused by low oil pressure, using too light a viscosity oil, oil breakdown, dirty oil or dirt in the crankcase, excessive blowby from worn rings and/or cylinders (gasoline dilutes and thins the oil), incorrect engine assembly (bearings too loose), loose or broken connecting rod bolts, or abusive driving.
Bearing wear can be checked by dropping the oil pan and inspecting the rod and main bearings. If the bearings are badly worn, damaged or loose, replacing the bearings may buy you some time. But if the bearings are badly worn or damaged, the crankshaft will probably have to be resurfaced -- which means a complete engine overhaul or replacing the engine is the vehicle is worth the expense.
ENGINE PINGS OR KNOCKS WHEN ACCELERATING
The cause here may be Spark Knock (Detonation) caused by an inoperative EGR valve, overadvanced ignition timing, engine overheating, carbon buildup in the combustion chambers, or low octane fuel.
Engine Noise Under LoadSymptom | Possible Cause | A cold piston knock for up to a minute and a half after starting a cold engine may be normal. This may be due to increased clearance between the pistons and cylinders. But once the engine warms up, the knocking noise should disappear.
If you hear a low rumble or knocking noise when the engine is warm, the most likely cause may be a bad rod bearing on the crankshaft (which may lead to bearing failure and/or rod breakage or crankshaft damage).
| Low oil pressure
| Check oil pressure at the oil pressure sending unit port on the engine with a gauge. .
If oil pressure is okay, replace sending unit.
| Detonation or spark knock
| May be due to low octane fuel, carbon buildup in combustion chambers, overadvanced ignition timing, inoperative EGR, or engine overheating.
Check all of these to determine the cause.
.
| Loose torque converter bolts
| Inspect the torque converter bolts and flywheel.
Repair as required.
| Cracked flywheel - automatic transmission
| Inspect the flywheel bolts and flywheel.
Repair as required.
| Excessive connecting rod or main bearing clearance
| Inspect connecting rod bearings , connecting rods and crankshaft. Use Plastigage or a feeler gauge to measure assembled bearing clearances.
| Excessive Piston clearance
| Piston slap may be due to worn cylinders, worn pistons or excessive piston-to-cylinder clearance
|
[ 本帖最后由 刘叔 于 29-4-2010 20:52 编辑 ] |
发表于 22-4-2010 21:48:51
收藏
赞
踩
楼主
发表于 27-4-2010 14:45:30
