另外，如果可以将这个贴打造成修水龙头的经验汇总贴就好了。作者: 5years 时间: 26-3-2013 10:24
How to Fix a Leaky Faucet with a Two Handle Design
如何修理漏水的水龙头（双把手）
[youtube]oRls_2q4AHA[/youtube]
Tired of a leaky faucet? Not only is it wasting money, but it is also wasting water. To repair a faucet, you will first need parts. You can either disassemble the faucet and take the parts to your local Lowe's, or you can by a faucet repair kit. You can also check the manufacturer's directions or the manufacturer's website for the exact parts for your faucet.
First, turn off your water supply. Then turn on of the faucet to relieve any residual pressure. Close or cover the drain. Place a towel in the drain to keep the parts in order and protect the sink. On some faucets, you can remove the handle or knob by prying off the cap, removing a screw, and pulling off the handle. Others can be removed by unscrewing a set screw.
Cartridge
To repair a cartridge style faucet, you will first have to remove the retaining clip or retaining nut. Then pull out the cartridge. If your cartridge is damaged or worn, just replace it with a new one. Then reassemble the faucet.
Compression and Reverse-Compression
To repair a compression or reverse-compression faucet, start by taking out the valve stem. On the bottom of the stem, remove the screw and washer and the old o-ring. Apply a little plumber's grease on the stem and add the new o-ring. Then reassemble your faucet and test it for leaks. If it still leaks, that means you valve seat might be damaged. Remove it and replace it.
Ceramic Disc
To repair a ceramic disc style faucet, start by unscrewing the mounting screws or retaining nut on the cylinder and pulling it out. Use a screwdriver to pry out the seals. Before replacing the seals, clean any buildup on the cylinder near the openings. Put the new seals in place, and then reassemble the faucet. When you turn on the water supply, make sure the faucet is in the on position and turn on the water slowly. Too much initial pressure can damage the ceramic discs in the cylinder.
Or head to our channel: http://www.youtube.com/Lowes作者: 5years 时间: 26-3-2013 10:27 标题: 如何修理水龙头漏水（单把） How to Fix a Leaky Faucet with a Single Handle Design
如何修理水龙头漏水（单把）
[youtube]A7e2bIfP8Us[/youtube]
faucet n. 龙头, 旋塞, (连接管子的)插口
-------------------------------- 视频的文字说明 --------------------
Uploaded on May 9, 2011
Let Lowe's guide you through steps for repairing a ball, cartridge or ceramic disk faucet. To repair a faucet, you will first need parts. You can either disassemble the faucet and take the parts to your local Lowe's, or you can by a faucet repair kit. You can also check the manufacturer's directions or the manufacturer's website for the exact parts for your faucet.
First, turn off your water supply. Then turn on of the faucet to relieve any residual pressure. Close or cover the drain. Place a towel in the drain to keep the parts in order and protect the sink.
Pry off any cover that may be over the set screw. Remove the screw and take off the handle. For vinyl handles, pry off the cap and remove the screw. If your model has one, remove the escutcheon. On some models you may have to remove the spout.
Rotating Ball Valve
To disassemble a faucet with a rotating ball valve, remove the cam, the washer and the ball. Carefully remove the seats and springs. If you took off the spout, replace the o-rings and add a little plumbers grease. Then replace the spout. Place the new seats on new springs and set them back in place. Replace the ball, washer and cam; reassemble the handle.
Cartridge
For a cartridge style faucet, first remove the handle. Remove the escutcheon too. Remove the retainer clip or nut. Pull out the cartridge body. If the cartridge is worn or damaged, just replace it. On some cartridges you can just replace the o-rings and add some plumbers grease. Reassemble the faucet.
Ceramic Disc
For a ceramic disc style faucet, start by unscrewing the retainer nut and puling it out. Use a screwdriver to lift out the seals. Before replacing the seals, clean any buildup on the cylinder near the openings. Put the new seals in place. Then reassemble the faucet. When you turn on the water supply, make sure the faucet is in the on position and turn on the water slowly. Too much initial pressure can damage the ceramic discs in the cylinder.作者: Samuel_ChenSJ 时间: 27-5-2014 12:24
